The South China Sea continental margin in the Qiongdongnan Basin (QDNB) area has incrementally prograded since 10.5 Ma generating a margin sediment prism more than 4km-thick and 150–200 km wide above the well-dated T40 stratigraphic surface. Core and well log data, as well as clinoform morphology and growth patterns along 28 2D seismic reflection lines, illustrate the evolving architecture and margin morphology; through five main seismic-stratigraphic surfaces (T40, T30, T27, T20 and T0) frame 15 clinothems in the southwest that reduce over some 200 km to 8 clinoforms in the northeast. The overall margin geometry shows a remarkable change from sigmoidal, strongly progradational and aggradational in the west to weakly progradational in the east. Vertical sediment accumulation rate increased significantly across the entire margin after 2.4 Ma, with a marked increase in mud content in the succession. Furthermore, an estimate of sediment flux across successive clinoforms on each of the three selected seismic cross sections indicate an overall decrease in sediment discharge west to east, away from the Red River depocenter, as well as a decrease in the percentage of total discharge crossing the shelf break in this same direction. The QDNB Late Cenozoic continental margin growth, with its overall increased sediment flux, responded to the climate-induced, gradual cooling and falling global sea level during this icehouse period. 相似文献
In thermal-related engineering such as thermal energy structures and nuclear waste disposal, it is essential to well understand volume change and excess pore water pressure buildup of soils under thermal cycles. However, most existing thermo-mechanical models can merely simulate one heating–cooling cycle and fail in capturing accumulation phenomenon due to multiple thermal cycles. In this study, a two-surface elasto-plastic model considering thermal cyclic behavior is proposed. This model is based on the bounding surface plasticity and progressive plasticity by introducing two yield surfaces and two loading yield limits. A dependency law is proposed by linking two loading yield limits with a thermal accumulation parameter nc, allowing the thermal cyclic behavior to be taken into account. Parameter nc controls the evolution rate of the inner loading yield limit approaching the loading yield limit following a thermal loading path. By extending the thermo-hydro-mechanical equations into the elastic–plastic state, the excess pore water pressure buildup of soil due to thermal cycles is also accounted. Then, thermal cycle tests on four fine-grained soils (natural Boom clay, Geneva clay, Bonny silt, and reconstituted Pontida clay) under different OCRs and stresses are simulated and compared. The results show that the proposed model can well describe both strain accumulation phenomenon and excess pore water pressure buildup of fine-grained soils under the effect of thermal cycles.
The Yangla deposit is an intrusion‐related Cu deposit in the Jinshajiang tectonic belt (eastern Sanjiang region, SW China). Despite extensive studies that have been conducted on this deposit, the relationship between the granitic magma and Cu mineralization is still unclear, and hence, the genesis is debated. To answer this question, we conducted an integrated study of mineralogy, fluid inclusions (FIs), and hydrogen and oxygen (H‐O) isotopes. Three mineralization stages were identified based on the ore textures, alteration zonation, and crosscutting relationships: (i) pre‐ore prograde skarn (stage I), with the garnet and pyroxene dominated by andradite and diopside, respectively; (ii) syn‐ore retrograde alteration (stage II), which is subdivided into the early syn‐ore stage (stage IIa) marked by retrograde hydrated mineral assemblages and significant Fe‐Cu‐Mo‐Pb‐Zn sulfide mineralization, and the late syn‐ore stage (stage IIb) featured by quartz‐calcite veins; and (iii) late supergene mineralization (stage III), which is characterized by secondary azurite and malachite. These results of mineralogy, FIs, and H‐O isotopes indicate that: (i) Cu mineralization has a close temporal, spatial, and genetic relationship with skarn alteration; (ii) the ore fluids were magmatic dominated with late‐stage meteoric water incursion; and (iii) Type‐S (halite‐bearing) and Type‐V (vapor‐rich) FIs coexisted in garnet and clinopyroxene of stage I, indicating that fluid boiling might have occurred during this stage. From stage I to stage IIa, the FI type transformed from Type‐S + Type‐V + Type‐L (liquid‐rich) to Type‐V + Type‐L with the conduct of mineralization and was accompanied by the disappearance of Type‐S, and homogenization temperature and salinity also tended to decrease dramatically, which may be caused by the deposition of skarn minerals. At stage IIa, boiling of the ore fluids still continued due to the change from lithostatic to hydrostatic pressure, which triggered the precipitation of abundant quartz‐Cu‐Mo‐Fe sulfides. Furthermore, fluid mixing between a high‐temperature magmatic fluid and a low‐temperature meteoric water might cause a considerable drop in temperature and the deposition of Cu‐bearing quartz/calcite veins during stage IIb. Hence, we consider the Yangla deposit to be of a skarn type, genetically related to the Mesozoic magmatism in the Sanjiang region. 相似文献
Journal of Geographical Sciences - Urban land intensive use is an important indicator in harmonizing the relationship between land supply and demand. The system dynamics (SD) can be used to... 相似文献
The forest litter is an essential reservoir of nutrients in forests, supplying a large part of absorbable base cations(BC) to topsoil, and facilitating plant growth within litter-soil system. To characterize elevational patterns of base cation concentrations in the forest litter and topsoil, and explore the effects of climate and tree species, we measured microclimate and collected the forest litter and topsoil(0-10 cm) samples across an elevational range of more than 2000 m(1243 ~ 3316 m a.s.l.),and analyzed the concentrations of BC in laboratory. Results showed that: 1) litter Ca concentration displayed a hump-shaped pattern along the elevational gradients, but litter K and Mg showed saddle-shaped patterns. Soil Ca concentration increased with elevation, while soil K and Mg had no significant changes. 2) Ca concentration in the forest litter under aspen(Populus davidiana) was significantly higher than that in all other species, but in topsoil, Ca concentration was higher under coniferous larch and fir(Larix chinensis and Abies fargesii). Litter K and Mg concentrations was higher under coniferous larch and fir, whereas there were nosignificant differences among tree species in the concentrations of K and Mg in topsoil. 3) Climatic factors including mean annual temperature(MAT), growing season precipitation(GSP) and non-growing season precipitation(NGSP) determined BC concentrations in the forest litter and topsoil. Soil C/N and C/P also influenced BC cycling between litter and soil. Observation along elevations within different tree species implies that above-ground tree species can redistribute below-ground cations, and this process is profoundly impacted by climate. Litter and soil Ca, K and Mg with different responses to environmental variables depend on their soluble capacity and mobile ability. 相似文献
The Micropile-Mechanically Stabilized Earth (MSE) wall, specially designed for mountain roads, is proposed to improve the MSE wall local stability, global stability and impact resistance of roadside barriers. Model tests and the corresponding numerical modeling were conducted to validate the serviceability of the Micropile-MSE wall and the reliability of the numerical method. Then, a parametric study of the stress and deformation of Micropile-MSE wall based on the backfill strength and interfacial friction angle between backfill and backslope is conducted to evaluate its performance. The test results indicate that the surcharge-induced horizontal earth pressure, base pressure and lateral displacement of the wall panel of Micropile-MSE wall decrease. The corresponding numerical results are nearly equal to the measured values. The basic failure mode of MSE wall in steep terrain is the sliding of backfill along the backslope, while A-frame style micropiles are capable of preventing the sliding trend. The maximum resultant displacement can be decreased by 6.25% to 46.9% based on different interfacial friction angles, and the displacement can be reduced by 6% ~ 56.1% based on different backfill strengths. Furthermore, the reduction increases when the interfacial friction angle and internal friction angle of backfill decrease. In addition, the lateral displacement of wall panel, the deformation of backfill decrease and the tension strain of geogrid obviously, which guarantees the MSE wall functions and provides good conditions for mountain roads. 相似文献
Northeast China experiences severe atmospheric pollution, with an increasing occurrence of heavy haze episodes. However, the underlying forces driving haze formation during different seasons are poorly understood. In this study, we explored the spatio-temporal characteristics and causes of haze events in Northeast China by combining a range of data sources(i.e., ground monitoring, satellite-based products, and meteorological products). It was found that the ‘Shenyang-Changchun-Harbin(SCH)'city belt was the most polluted area in the region on an annual scale. The spatial distribution of air quality index(AQI) values had a clear seasonality, with the worst pollution occurring in winter, an approximately oval-shaped polluted area around western Jilin Province in spring, and the best air quality occurring in summer and most of the autumn. The three periods that typically experienced intense haze events were Period I from mid-October to mid-November(i.e., late autumn and early winter), Period II from late-December to February(i.e., the coldest time in winter), and Period III from April to mid-May(i.e., spring). During Period I, strong PM_(2.5) emissions from seasonal crop residue burning and coal burning for winter heating were the dominant reasons for the occurrence of extreme haze events(AQI 300). Period II had frequent heavy haze events(200 AQI 300) in the coldest months of January and February, which were due to high PM_(2.5) emissions from coal burning and vehicle fuel consumption, a lower atmospheric boundary layer, and stagnant atmospheric conditions. Haze events in Period III, with high PM_(10) concentrations, were primarily caused by the regional transportation of windblown dust from degraded grassland in central Inner Mongolia and bare soil in western Jilin Province. Local agricultural tilling could also release PM_(10) and enhance the levels of windblown dust from tilled soil. Better control of coal burning, fuel consumption, and crop residue burning in winter and autumn is urgently needed to address the haze problem in Northeast China. 相似文献